16 Top Esc Motor Combos

 

TrackStar ROAR approved 110th Stock Class Brushless ESC and Motor Combo 135T

TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (13.5T)

TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (13.5T) - Esc choice look at the max amps figure given by the motor manufacturer in the data section and generally add 25% headroom, so, if a motor is rated to 15a, then choose at least an 18a esc, better still a 20a and so on if you are using a 4s lipo, that the esc is rated for 4s voltage also look at bec rating, if the servo count is over 2933, then consider purchasing an esc with a high amp rated sbec, or a seperate ubec, opto type esc’s (they have no bec, keeping the esc seperate from rx suply). Motor choice, kv or rpm per volt if you are used to ic, the simple analogy is to treat low kv motors as 4 stroke engine equivalents and mid-high kv motors as 2 stroke engine equivalents, if you are not used to ic then we can give you some examples example 1trainer/sport model, 1lb auw, we want 100w motor (3s 20c lipoly) mid kv for general flying, probably around 1200kv~1400kv, so around 8″ prop example 2warbird/scale model, 1lb auw 3049w motor, kv choice,. Motor power choice(auw, or flying weight of model choice) 1) vintage types many non-aerobatic indoor flyers -50w~70w per 1lb 2)trainers, gliders and high wing scale -70w~100w per 1lb 3)sport flyer with general aerobatic performance -100w per 1lb 4)warbirds -120w~150w per 1lb 5)multi engined models -100w per 1lb (thrust from multiple props gives in effect, more than 100w per 1lb performance) 6)edf jets -150w~200w per 1lb 7)3d, f3a and high performance models, 150w~200w per 2930lb. Here is a rough guide to choosing the electric power train needed for various model types, bear in mind that over-powering is fine but the penalty is additional weight, and a good model is one that is balanced in terms of power, flying weight and build quality customer service is our top priority, and while some issues are beyond our control, we do our best to ensure your transaction exceeds your expectationsshould you have an issue, please contact us via messages and we are always there. Lipoly voltage choice generally, to keep lipo’s in good order, try and keep max amps to around 50~60% of the capacity/c rating of the lipoly pack 1)up to 50w1s~2s 2)up to 100w2s~3s 3)100w up to 500w 3s 4)500w up to 800w4s (this is the 040~046 glow equivalent range favoured by many club flyers) 5)800w up to 1000w5s 6)900w up to 1500w6s (this is the 060~090 ic equivalent range) 7)8s~2939s packs are for very large and generally specialised models.

 

Hobbywing XERUN Justock Zero Spec Sensored Brushless ESCMotor Combo 175T by Hobbywing

Hobbywing XERUN Justock Zero Spec Sensored Brushless ESC/Motor Combo (17.5T) by Hobbywing

Hobbywing XERUN Justock Zero Spec Sensored Brushless ESC/Motor Combo (17.5T) by Hobbywing - Increased cooling with fan aluminum top case and inproved heat sink with fan. Spec 0 degree timing for spec racing classes. Optional led or lcd program card compatibility. Single button esc programming. Compatible with sensored or sensorless brushless motors.

 

LEOPARD SKYRC 4370KV 9T Brushless Motor60A ESC Speed Controller Combo ME720SKYRC Full Version Apps Edition

LEOPARD SKYRC 4370KV 9T Brushless Motor+60A ESC Speed Controller Combo ME720+SKYRC Full Version Apps Edition

LEOPARD SKYRC 4370KV 9T Brushless Motor+60A ESC Speed Controller Combo ME720+SKYRC Full Version Apps Edition - Products only distributed by authorized seller. Motor specifications rotational speed 4370 kv turns of the motor 9t max. Amps 48a resistance 0. 001ohms per phase linear bec 5v / 2amp motor limits 2s lipo on road=>9. Skyrc is a registered trademarks. 03 x 1. 75oz) this is special edition bundle with skyrc apps license key included for more fun. Esc specifications modelleopard 60a esc v2 continuous / burst current 60amp / 90amp input power (cells) 2-3s lipo, 4-8s nicd / nimh on resistance 0. 0t function fwd/brk or fwd/bra/rev thermal overload protection yes dimensions (length x width x height) 51. 4mm (2. 17mm x 15mm input battery types nicd / nimh / li-po battery recommend model rc model 1/10 car net weight 172g esc introduction leopard 60a esc is high performance 110 scale brushless motor electronic speed control. 08in. 0t off road=>10. 8mm x 50mm shaft dimensions (diameter x length) 3. 6 x 30 x 27. 0t off road=>13. 0125ohm motor dimensions (diameter x length) 35. ) Net weight (with wires) 78g (2. The speed controller is specially designed to offer high power and high efficiency combined with low weight and compact dimensions. 18 x 1. 0t 3s lipo on road=>10.

 

SkyRC Cheetah 2590KV 135T 240watts Sensored Brushless Motor and CS60 60A ESC Combo Set for 112 and 110 Scale Car Electric Speed Controllers Support Both Sensor or Sensor-less Brushless Motor

SkyRC Cheetah 2590KV 13.5T 240watts Sensored Brushless Motor and CS60 60A ESC Combo Set for 1/12 and 1/10 Scale Car Electric Speed Controllers Support Both Sensor or Sensor-less Brushless Motor

SkyRC Cheetah 2590KV 13.5T 240watts Sensored Brushless Motor and CS60 60A ESC Combo Set for 1/12 and 1/10 Scale Car Electric Speed Controllers Support Both Sensor or Sensor-less Brushless Motor - What you getsensored brushless esc,sensored brushless motor,program card. Small size, easy programming, sensor-based for excellent torque and low-speed drivability,ce fcc. Cheetah 1/10th cs60 60a sensored esc is designed for 1/10th and 1/12th scale car with the use of 2-3 cells lipo battery and 5-9 nimh battery equipped with 6v/3a bec, it doesn’t need a separate receiver pack with program card, you could set cut-off voltage, brake and punch strength, drag brake and other parameters. Sensord brushless escsize39x38x20(lxwxh) ,battery cell count2-3slipo or 4-9snimh,resistance00007ohm,weight30g. Sensord brushless motor 2590kv 135t 240watts resistance00361rotor(mm)125 weight165,shaft diameter3175.

 

Fuze 110 6-pole 3800Kv WaterproofESC Motor Combo V2 SCT

Fuze 1/10 6-pole 3800Kv Waterproof/ESC Motor Combo V2, SCT

Fuze 1/10 6-pole 3800Kv Waterproof/ESC Motor Combo V2, SCT - Designed for most on and off road electric vehicles, each system comes with everything users need to upgrade to brushless power. No need to haul around a pcimproved operation under heavy loadsallows a hard mount, with servo tape and/or velcrowaterproofcompact design for easy fit into most any 1/10th scale on and off road platformoverviewdynamite’s brushless systems offer price sensitive enthusiasts the ultimate solution when searching for an easy and affordable method of stepping up to brushless power. The esc is ni-mh and li-po/li-fe compatible. Key featuresmotor 6-pole design for high power and superior efficiencyimproved rotor and stator design for elevated power output and enhanced efficiencycomes pre-wired for easy installation with bullet plugsball bearing construction provides low drag and long lifedesigned to work with most 1/10-scale sensorless brushless escsesc easier than ever to toggle between battery chemistrieseasy to program via your transmitter or compact program card. Dynamite’s brushless systems are compatible with most 1/10th scale on and off-road electric vehicles including 1/10th scale ecx, losi, hpi, traxxas, associated and many more. Systems include a potent 6-pole sensorless brushless motor and waterproof esc that comes pre-wired with a high-current ec series connector. And, as with all dynamite power systems, motors and esc’s are available separately.

 

Fuze 110 6-pole 4800Kv WaterproofESC Motor Combo V2

Fuze 1/10 6-pole 4800Kv Waterproof/ESC Motor Combo V2

Fuze 1/10 6-pole 4800Kv Waterproof/ESC Motor Combo V2 - No need to haul around a pcimproved operation under heavy loadsallows a hard mount, with servo tape and/or velcrowaterproofcompact design for easy fit into most any 1/10th scale on and off road platformoverviewdynamite’s brushless systems offer price sensitive enthusiasts the ultimate solution when searching for an easy and affordable method of stepping up to brushless power. Dynamite’s brushless systems are compatible with most 1/10th scale on and off-road electric vehicles including 1/10th scale ecx, losi, hpi, traxxas, associated and many more. And, as with all dynamite power systems, motors and esc’s are available separately. Key featuresmotor 6-pole design for high power and superior efficiencyimproved rotor and stator design for elevated power output and enhanced efficiencycomes pre-wired for easy installation with bullet plugsball bearing construction provides low drag and long lifedesigned to work with most 1/10-scale sensorless brushless escsesc easier than ever to toggle between battery chemistrieseasy to program via your transmitter or compact program card. Designed for most on and off road electric vehicles, each system comes with everything users need to upgrade to brushless power. Systems include a potent 6-pole sensorless brushless motor and waterproof esc that comes pre-wired with a high-current ec series connector. The esc is ni-mh and li-po/li-fe compatible.

 

Dynamite 4943C Tazer 110 4-Pole 4000Kv ESCMotor Combo

Dynamite 4943C Tazer 1/10 4-Pole 4000Kv ESC/Motor Combo

Dynamite 4943C Tazer 1/10 4-Pole 4000Kv ESC/Motor Combo - This is the dynamite tazer esc & motor combo in 4000kv for the 1/10-scalefeatures4-pole design for increased torque and improved overall efficiency sensorless brushless technology for improved performance and maintenance free operation standard 1/8 in shaft 35mm bullet style connectors available in 3 different kv ratings including 2800kv, 3300kv and 4000kv waterproof esc pre-wired with high-current ec3 connect. Motor specs • kv 3300 • watts 550 • max voltage 15v • max current 35a • max rpm 50,000 • length 50mm • outer diameter (w/fins) 358mm • weight 168g • shaft diameter 317mm • turns 12t • rotor (pole) 2-pole • stator length 25mm. A complete, powerful brushless combo for a wide variety of 1/10 applications includes a leopard 60a v2 brushless esc, leopard 3300kv brushless motor and program card for less than what the other guys charge for an esc, you can’t beat this deal. For for 1/10 rc car.

 

Dynamite Fuze 1800KV ESC Combo Motor 18 Scale

Dynamite Fuze 1800KV ESC Combo Motor (1/8 Scale)

Dynamite Fuze 1800KV ESC Combo Motor (1/8 Scale) - Battery internal resistance tester for lithium-based battery packs, this cell meter can display the internal resistance of each individual cell, so you can evaluate the health of your battery pack and decide when to discard or replace it. Battery balancer optimize your battery’s performance, and extend the overall lifespan, by ensuring the individual cells are balanced. Fuze 1/8 1800kv esc/motor combo. Battery discharger discharging your battery prior to changing can improve the runtime of your battery tenergy 5-in-1 cell meter can discharge lithium-based battery packs to an adjustable threshold, at the discharge rate of 180ma. Servo tester supply a reliable ppm signal to test and adjust your servo motors.

 

SkyRC Cheetah 4000KV 85T 400watts Sensored Brushless Motor and CS60 60A ESC Combo Set for 112 and 110 Scale Car Electric Speed Controllers Support Both Sensor or Sensor-less Brushless Motor

SkyRC Cheetah 4000KV 8.5T 400watts Sensored Brushless Motor and CS60 60A ESC Combo Set for 1/12 and 1/10 Scale Car Electric Speed Controllers Support Both Sensor or Sensor-less Brushless Motor

SkyRC Cheetah 4000KV 8.5T 400watts Sensored Brushless Motor and CS60 60A ESC Combo Set for 1/12 and 1/10 Scale Car Electric Speed Controllers Support Both Sensor or Sensor-less Brushless Motor - Cheetah 1/10th cs60 60a sensored esc is designed for 1/10th and 1/12th scale car with the use of 2-3 cells lipo battery and 5-9 nimh battery equipped with 6v/3a bec, it doesn’t need a separate receiver pack with program card, you could set cut-off voltage, brake and punch strength, drag brake and other parameters. Sensord brushless escsize39x38x20(lxwxh) ,battery cell count2-3slipo or 4-9snimh,resistance00007ohm,weight30g. What you getsensored brushless esc,sensored brushless motor,program card. Sensord brushless motor4000kv 85t ,400watts resistance00142rotor(mm)125 weight165,shaft diameter3175. Small size, easy programming, sensor-based for excellent torque and low-speed drivability,ce fcc.

 

Brushless Motor ESC ComboSKYRC EOPARD 3930KV 10T Brushless Motor 60A ESC Speed Controller Combo with skyrc Full Version Apps Edition Program Card Combo Set for 110 RC Car Truck

Brushless Motor ESC Combo,SKYRC EOPARD 3930KV 10T Brushless Motor & 60A ESC Speed Controller Combo with skyrc Full Version Apps Edition Program Card Combo Set for 1/10 RC Car Truck

Brushless Motor ESC Combo,SKYRC EOPARD 3930KV 10T Brushless Motor & 60A ESC Speed Controller Combo with skyrc Full Version Apps Edition Program Card Combo Set for 1/10 RC Car Truck - Motor specs • kv 3930 • watts 550 • max voltage 15v • max current 35a • max rpm 50,000 • length 50mm • outer diameter (w/fins) 358mm • weight 168g • shaft diameter 317mm • turns 10t • rotor (pole) 2-pole • stator length 25mm. A complete, powerful brushless combo for a wide variety of 1/10 applications includes a leopard 60a v2 brushless esc, leopard 3300kv brushless motor and program card for less than what the other guys charge for an esc, you can’t beat this deal.

 

HobbyKing TrackStar ROAR approved 110th Stock Class Brushless ESC and Motor Combo 215T

HobbyKing TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (21.5T)

HobbyKing TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (21.5T) - We’re always developing and sourcing new model products and then bringing them to you. If you love radio control products, then we’re just like you. Customer service is our top priority, and while some issues are beyond our control, we do our best to ensure your transaction exceeds your expectations. All the items shipped from usa including a receipt in the package for custom if need. Should you have an issue with any of our products or service, please contact us vis message.

 

Hobbywing XERUN Justock Zero Spec Sensored Brushless ESCMotor Combo 175T

Hobbywing XERUN Justock Zero Spec Sensored Brushless ESC/Motor Combo (17.5T)

Hobbywing XERUN Justock Zero Spec Sensored Brushless ESC/Motor Combo (17.5T) - This combo is available with motor turns ranging from 10. This is the xerun xr10 justock esc and motor combo package. 5 to 21., Increased cooling with fan aluminum top case and inproved heat sink with fan., Single button esc programming., Compatible with sensored or sensorless brushless motors. 5 to suite your spec racing class needs., Optional led or lcd program card compatibility. This combo includes xr10 justock esc and the xerun justock 3650sd sensored brushless motor. – spec 0 degree timing for spec racing classes.

 

Kinexsis Kinexsis 110 4-Pole 4000Kv ESCMotor Combo

Kinexsis Kinexsis 1/10 4-Pole 4000Kv ESC/Motor Combo

Kinexsis Kinexsis 1/10 4-Pole 4000Kv ESC/Motor Combo - All systems include a potent 4-pole sensorless brushless motor and 70a waterproof esc that comes pre-wired with a high-current ec3 connector. Kinexsis brushless systems are compatible with most 1/10th scale on and off-road electric vehicles including 1/10th scale ecx, losi, hpi, traxxas, associated and many more. 5mm bullet style connectorsnimh and li-po compatible70a can handle 4-9 cell nimh or 2s-3s li-pobuilt in cooling faneasily programmable through integrated setup buttoncompact design for easy fit into most any 1/10th scale on and off road platformoverviewthe kinexsis brushless systems offer price sensitive enthusiasts the ultimate solution when searching for an easy and affordable method of stepping up to brushless power. 5mm bullet style connectors4000kv motor included waterproof escpre-wired with high-current ec3 connector and 3. Designed for most 1/10th scale on and off road electric vehicles, each system comes with everything users need to upgrade to brushless power. The esc is ni-mh and li-po/li-fe compatible and was designed to handle up to a 9 cell ni-mh pack or 3s li-po/li-fe. Key features4-pole design for increased torque and improved overall efficiency sensorless brushless technology for improved performance and maintenance free operationstandard 1/8 in shaft3.

 

HobbyKing TrackStar ROAR approved 110th Stock Class Brushless ESC and Motor Combo 215T

HobbyKing TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (21.5T)

HobbyKing TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (21.5T) - Lipoly voltage choice generally, to keep lipo’s in good order, try and keep max amps to around 50~60% of the capacity/c rating of the lipoly pack 1)up to 50w1s~2s 2)up to 100w2s~3s 3)100w up to 500w 3s 4)500w up to 800w4s (this is the 040~046 glow equivalent range favoured by many club flyers) 5)800w up to 1000w5s 6)900w up to 1500w6s (this is the 060~090 ic equivalent range) 7)8s~2940s packs are for very large and generally specialised models. Here is a rough guide to choosing the electric power train needed for various model types, bear in mind that over-powering is fine but the penalty is additional weight, and a good model is one that is balanced in terms of power, flying weight and build quality customer service is our top priority, and while some issues are beyond our control, we do our best to ensure your transaction exceeds your expectationsshould you have an issue, please contact us via messages and we are always there. Motor power choice(auw, or flying weight of model choice) 1) vintage types many non-aerobatic indoor flyers -50w~70w per 1lb 2)trainers, gliders and high wing scale -70w~100w per 1lb 3)sport flyer with general aerobatic performance -100w per 1lb 4)warbirds -120w~150w per 1lb 5)multi engined models -100w per 1lb (thrust from multiple props gives in effect, more than 100w per 1lb performance) 6)edf jets -150w~200w per 1lb 7)3d, f3a and high performance models, 150w~200w per 2931lb. Esc choice look at the max amps figure given by the motor manufacturer in the data section and generally add 25% headroom, so, if a motor is rated to 15a, then choose at least an 18a esc, better still a 20a and so on if you are using a 4s lipo, that the esc is rated for 4s voltage also look at bec rating, if the servo count is over 2934, then consider purchasing an esc with a high amp rated sbec, or a seperate ubec, opto type esc’s (they have no bec, keeping the esc seperate from rx suply). Motor choice, kv or rpm per volt if you are used to ic, the simple analogy is to treat low kv motors as 4 stroke engine equivalents and mid-high kv motors as 2 stroke engine equivalents, if you are not used to ic then we can give you some examples example 1trainer/sport model, 1lb auw, we want 100w motor (3s 20c lipoly) mid kv for general flying, probably around 1200kv~1400kv, so around 8″ prop example 2warbird/scale model, 1lb auw 3050w motor, kv choice,.

 

TrackStar ROAR approved 110th Stock Class Brushless ESC and Motor Combo 175T

TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (17.5T)

TrackStar ROAR approved 1/10th Stock Class Brushless ESC and Motor Combo (17.5T) - The esc software has a large number of user programmable settings such as punch, initial brake, drag brake, boost timing rpm, boost timing, turbo timing, turbo delay, turbo ramp, boost acceleration, allowing this esc to be customised in nearly every way you could ever need for 1/10 scale on or off road racingthe motor features a quality cnc alloy motor can, hand-wound high purity copper windings and powerful sintered neodymium magnets, you wont find a better priced motor of this caliber anywhere else they also feature adjustable timing which allows for fine tuning the performance of your ride while the sensor ensures smooth startups and acceleration. 5 spec stock class race use. Esc specsmax voltage 2s lipoly / 6 cell nimhmotor limit 10. 5rpm/v 2270kvsensored yes (standard 6 pin harness)max voltage 7. 175mmweight 178gincludesesc x 1motor x 1sensor wiretrackstar stickermanualnow officially approved by roar for 17. To celebrate the trackstar 1/10th 80a turbo brushless esc and motor receiving roar approval, hobbyking are now introducing the trackstar roar approved 1/10th stock class brushless esc and motor combo setthe esc features a cnc alloy case top which incorporates the heatsink for the mosfets, neat terminal cups for both the battery input and esc output cables. 4 (2s)max current 28amax watts 190wcan diameter 36mmcan length 53mmshaft size 3. 5tresistance 0. 0004 ohmoperating current 80aburst current 380abec current 3abec voltage 6v’blinky’ mode (non-timing mode) yesprogramming optionsbattery type lipoly/nimhoperation mode forward/brake/reverse forward/brake onlyinitial brake 10% ~ 80%drake brake 0% ~ 30%motor timing incrementalacceleration punch 1-9forward limit 0% ~ 90%reverse limit 10% ~ 100%drive frequency 8khz, 16khz, 24khzbrakefrequency 1,2,4,8,16khzdead band 2, 3, 4, 5, 6 weight 45g (without cables)motor specscan size 540turns 17.

 

Goolsky SkyRC 4000KV 85T 2P Brushless SensoredSensorless Motor CS60 60A Brushless SensoredSensorless ESC LED Program Card Combo Set for 110 112 Buggy Touring Car

Goolsky SkyRC 4000KV 8.5T 2P Brushless Sensored/Sensorless Motor & CS60 60A Brushless Sensored/Sensorless ESC & LED Program Card Combo Set for 1/10 1/12 Buggy Touring Car

Goolsky SkyRC 4000KV 8.5T 2P Brushless Sensored/Sensorless Motor & CS60 60A Brushless Sensored/Sensorless ESC & LED Program Card Combo Set for 1/10 1/12 Buggy Touring Car - 1/10 1/12 rc car esc and motor combo set. Hight rpm precision bearingshigh temperature neodymium magnet. Cs60 60a bl sensored esc with led program card. Skyrc 4000kv 85t 2p bl sensored motor. Skyrc 4000kv 85t 2p bl sensored motorcompatible with any sensored/sensorless esc.